Hubs & Parts

Excellent condition. Sold as a left and right pair. Made in England. 5/16 inch x 26TPI. Chrome plated steel construction. Integrated toothed washer. Chrome finish is in excellent condition. Phillips Club Wing Nuts 5/16in 26TPI Pair

Good condition. Hub is fully functional. 40 hole. 3/8in axle with reduced section where it slides into the frame drop-outs. 108mm OLD. Manufactured circa 1970s. Chrome is very good with some minor scratches. Includes axle nuts. Drive side dust cap is missing. Grease port is intact. Includes 18 tooth...

RockShox Maxle Lite Front Thru Axle 15x100mm (125mm Length) The tool-free Maxle Lite Front brings exceptional stiffness and durability to your ride in a light, easiest-to-use expanding wedge thru axle system. Rock Shox part number: 00.4318.000.000 Specs: Axle Diameter (mm) 15 Overall Length (mm) 125...

Good condition. For Rohloff Speedhub dual cable hubs. Mounts to the brake post in place of the usual brake bolt. Aluminum holder and hardware. All threads are in good condition. Rohloff Brake Post Mount Cable Hanger

Good condition. For Sachs 3x7 internallly geared hubs. One end attaches to the cable and the other clips to the hub chain for quick adust and release. Sachs 3x7 Hub Chain Cable Connector

New old stock. Maillard number 3312/1. 5/16in diameter. 4 1/8in long. Includes: Axle x 1. Cones x 2. Washers x 2. Locknuts x 2. Sachs Maillard Axle for Atom-Normandy Hub 4 1/8in - NOS

Excellent condition. Near mint. Chrome is perfect. 147mm between nuts with lever closed. Includes centring springs. Lever stamped "SACHS MAILLARD" on outside, "MADE IN FRANCE" on inside. Sachs Maillard Rear Quick Release Skewer

New old stock. Kit is complete. New in the box. 137 repair parts for Shimano 333 F-type and other hubs. Kit contains the following part numbers: 321-5200 x 2 321-9014 x 2 321-9017 x 1 321-9009 x 1 321-9022 x 1 321-9023 x 2 321-0600 x 10 321-0700 x 5 321-1200 x 10 321-1300 x 5 321-9029 x 2 321-5500 x...

Good working condition. Tested - 3 gears and brake all function properly. 112mm over locknut dimension. 36 hole. 18 tooth cog. Includes shift rod, bell crank, 1 axle nut and washer. Chrome finish has deteriorated on the hub shell. Bell crank has some surface rust. Oil port is intact and functional. Shimano...

Good working condition. Tested - 3 gears and brake all function properly. 112mm over locknut dimension. 36 hole. 18 tooth cog with minimal wear. Includes shift rod, bell crank, axle nuts and washers. Chrome finish is very good throughout. Oil port is intact and functional. Shimano 3SC 3 Speed Coaster...

Good condition. Bearings are very smooth. 36 hole. 120mm OLD. 10mm hollow axle. Finish is in good condition with some minor scratches. First generation Dura-Ace manufactured from 1873-84. Unclear whether model HS-831 or HB7110. Designed for 5 or 6 speed freewheel. Made in Japan. Shimano Dura-Ace 1st...

New old stock. Genuine Shimano replacement part. No dust cover. External threads to accept threaded cog style cassettes. For use with Shimano FH-HG50 5 speed hubs. Will fit some other 5 speed models. Shimano FH-HG50 5sp Freehub Body - NOS

Good condition. Bearings are reasonably smooth. 36 hole. 100mm OLD. 9mm hollow axle. Finish is lightly tarnished with moderate scratches throughout. Decal is good but peeling at one end. Made in Japan. Shimano HB-1050 105 Front Hub 36 Hole

Fair condition. Bearings are a bit stiff and dry from age - should be serviced before use. Freehub functions properly but feels a little dry. Freehub Body is 5 speed compatible. Accepts cassette with thread-on outer cog. 10mm hollow axle. 126mm over locknut diameter. Finish is lightly tarnished with...

New old stock. Fits Sturmey Archer GH6 Dynohub generator hub. Sturmey Archer GH6 hub exploded view is here: http://www.sturmey-archerheritage.com/images/photos/pic-62.1.jpg Sturmey Archer part number: LB358Z. Sturmey Archer Right Cone for GH6 Dynohub LB358Z - NOS

Good condition. Sold as a left and right pair. Made in Japan. 3/8 inch. 26TPI. Aluminum construction. Integrated toothed washer. Finish has moderate scrapes and scratches from use. Toothed washers have some tarnish from age. Sugino Aluminum Wing Nuts 3/8in 26TPI

Excellent condition. Chrome is very good. 134mm between nuts with lever closed. Includes centring springs. Sunshine Rear Quick Release Skewer 134mm

New old stock. The Superbe Pro hubs are the longest mass produced pair of Road Racing hubs using precision sealed cartridge bearings. The hub shells are forged as a single piece of aluminum alloy, then polished to achieve a mirror like finish. The front hub is drilled through for the axle and bored from...

Good condition. 100mm OLD. 32 hole. Sealed cartridge bearings with Grease Guard ports for lubrication. Bearings are reasonably smooth. Hub shell has a few light scuffs and scratches. 9mm axle is straight. Suntour XC Pro Grease Guard Front Hub

New old stock. 28 hole. 3/8in axle. 126mm OLD. Designed to accomodate 5 or 6 speed freewheel. Includes mounting nuts. Hub has been built up but not used. Some minor blemishes on the chrome from age. Made by Suzue in Japan. Suzue 28 Hole Steel Rear 5-6 Speed Threaded Hub - NOS

New old stock. 3/8in solid axle with flats. 140mm overall length for front hub. 63.8mm bearing shoulder spacing. For Suzue sealed bearing hubs. Finish has some minor blemishes from age. Made in Japan.

New old stock. 36 hole. 3/8in axle. 110mm OLD. Designed to accomodate a single speed freewheel. Includes mounting nuts. Hub has been built up but not used. Some minor blemishes on the chrome from age. Made by Suzue in Japan. Suzue 36 Hole Steel Rear Single Speed Threaded Hub - NOS

New old stock. Hollow QR axle. For Suzue sealed bearing hubs. Made in Japan. 110mm x 9mm front. 135mm x 10mm rear. Select form drop-down menu. Suzue 9mm & 10mm Hollow Axle for Sealed Hub - NOS

Excellent condition. Sealed cartridge bearings are smooth. 36 hole. 10mm hollow axle. 123mm over locknut dimension. Designed to accomodate 5 or 6 speed freewheel. Some minor scratches from use. Made by Suzue in Japan. Suzue Sealed-Tech 36 Hole Rear 5-6 Speed Threaded Hub

Good condition. Finish has moderate scuffs and scratches throughout. Sealed cartridge bearings are reasonably smooth. 36 hole. 3/8in axle. 126mm OLD. Designed to accomodate 6 or 7 speed freewheel. Includes mounting nuts. Date stamped 1978. Made by Suzue in Japan. Suzue Sealed-Tech 36 Hole Rear 6-7 Speed...

Fair condition. 18 (36) tooth skip tooth sprocket. Sprocket shows significant wear. Takes 5/8in through axle. 104.5mm OLD. 36 hole. Bearings are reasonably smooth. Finish is tarnished throughout. Unbranded Antique Fixed Gear Through Axle Hub

New old stock. Left and right pair. Made in Germany. 3/8in. 26TPI. Chrome plated broaze construction. Integrated toothed washer. Mint consition. Verma Bronze Wing Nuts 3/8in 26TPI Pair - NOS

New old stock. Made in Shawinigan, Quebec, Canada. 114mm overall width. 3/8in inside diameter. 50mm spoke hole circle. 84mm flange centre to flange centre. 36 hole. Drilled for 12 gauge spokes. Aluminum hub shell. Equipped with a grease nipple for easy maintenance. Some light scuffs and scratches from...

New old stock. Maillard number 3010. 5/16in diameter. 5 1/8in long. Includes: Axle x 1. Cones x 2. Spacers x 2. Locknuts x 2. Axle nuts x 2. Maillard Axle for Atom-Normandy Hub 5 1/8in - NOS

Good condition. Bearings are slightly rough - should be serviced before installation. Freehub engages properly. Freehub Body is 7 speed compatible. 10mm hollow axle. 36 hole. Finish is lightly tarnished with moderate scuffs and scratches. Date stamped 1990. 130mm or 135mm OLD - please select from drop-down...